PLUMBING BASICS: AN ESSENTIAL FOR INSTALLING A BATHTUB

Plumbing Basics: An Essential for Installing a Bathtub

Plumbing Basics: An Essential for Installing a Bathtub

Blog Article

Call

What are your opinions about Tools You Need to Install a New Bathtub ?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bath tub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, and also in some cases, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging job. If the old tub is conveniently obtainable, the project can relocate easily; if you need to open a wall surface to get rid of the old tub as well as place the new bathtub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need an assistant to vacate the old bathtub and set in the brand-new one. Make sure you have qualified on your own for the task and fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to consider using one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will aid you set up a new bath tub in your bathroom if you have actually currently purchased a brand-new bathtub and do not need to alter the setup of your previous water system pipelines.
Your tools and material checklist ought to make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installment


    First of all, the sustaining frame provided with the bathroom needs to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps unit to prevent pressure on the bathtub.
    Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final placement.

    Removing Old Touches


    If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be quite troublesome due to the restricted access that is usually the instance.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the staying water that will come from the pipelines. As soon as the supply pipelines have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing compound.
    Before moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

    Setting up the Tub


    Making use of both wood boards under its feet, position the tub in the required setting. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little points.
    The following objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bath tub up until the level checks out degree.
    To mount faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
    Activate the water system and examine all joints and new pipework for leakages and also tighten them if needed. Load the bath tub as well as additionally inspect the overflow outlet as well as the regular electrical outlet for leaks.
    Ultimately, deal with the bath paneling as defined in the producer's user's manual. Tiling and also securing around the bath tub should wait till the bath tub has actually been used at the very least once as this will settle it right into its final position.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, then you will require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipelines.
    If you require to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
    Next, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in location in between the tap and the sink. Safeguard the faucet in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type should be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the area where the bath meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall surface between the bathroom and the tiling, bring about issues with wetness as well as feasible leaks to the ceiling listed below.
    You can pick from a range of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and also cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to permit the activity experienced when the tub remains in usage. The sealer can crack fairly very early if you do not take into consideration this motion prior to securing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant glue as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I ran across that content about Installing A Bathtub when browsing the internet. Enjoyed our write up? Please share it. Let other people discover it. We thank you for reading our article about Installing A Bathtub.


    Emergency plumber? One call away.

    Report this page